MCP6021-E/P
| Parameters | |
|---|---|
| Power Supply Rejection Ratio (PSRR) | 74dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 500μV |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Height | 4.953mm |
| Length | 10.16mm |
| Width | 7.112mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2003 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | Not Applicable |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Base Part Number | MCP6021 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Operating Supply Current | 1mA |
| Nominal Supply Current | 1mA |
| Output Current | 22mA |
| Slew Rate | 7V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~5.5V |
| Output Current per Channel | 30mA |
| Input Offset Voltage (Vos) | 250μV |
| Bandwidth | 10MHz |
| Unity Gain BW-Nom | 10000 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.005μA |
MCP6021-E/P Overview
It is packaged in an 8-DIP (0.300, 7.62mm)-case that protects the operational amplifiers from damage. An op amp of this type is a General Purpose-type. The op amp is delivered to you in a Tube case. It is estimated that there will be at least 8 terminations this year. Linear amplifier has a total of 8 pins. As a reminder, this buffer op amp should be powered by 5V battery and that the battery should be inserted in the amplifier. In order to be more specific, this instrumentation amplifier is one of the types of Operational Amplifier devices. There are 8 pins on this chip. As far as the input offset voltage is concerned, linear amplifier rates at 250μV. It is recommended that this electronic component be mounted using the Through Hole mounting type. In relation to the operating temperature of this buffer op amp, it works well at an average of -40°C~125°C . Operational amplifier can operate supply current at 1mA. There should be no change in the voltage gain. 1 channels are available on the instrumentation amplifier. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages.
MCP6021-E/P Features
8 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
MCP6021-E/P Applications
There are a lot of Microchip Technology MCP6021-E/P Instrumentational OP Amps applications.
- E-book readers
- Switching amplifier
- RF cable systems
- Communication device
- Power transmission
- Industrial control system
- Exponential operation circuits
- MP3
- Band-stop filter
- Blood pressure sensors
