MCP6021-I/SN
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2005 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6021 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Nominal Supply Current | 1mA |
| Output Current | 22mA |
| Current - Supply | 1mA |
| Slew Rate | 7V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~5.5V |
| Input Offset Voltage (Vos) | 500μV |
| Bandwidth | 10MHz |
| Unity Gain BW-Nom | 10000 kHz |
| Voltage Gain | 110dB |
| Power Supply Rejection Ratio (PSRR) | 74dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Current - Output / Channel | 30mA |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Height | 1.2446mm |
| Length | 4.8768mm |
| Width | 3.9116mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6021-I/SN Overview
It is packaged in an 8-SOIC (0.154, 3.90mm Width)-case that protects the operational amplifiers from damage. An op amp of this type is a General Purpose-type. A Tube case is used for delivering the op amp. It is estimated that there will be 8 terminations in the next few months. The pins on this board total to 8 in total. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. This particular linear amplifier is a type of Operational Amplifier device, to be precise. In total, the buffer amplifier consists of 8 pins. In terms of input offset voltage, operational amplifier rates 500μV. It is recommended that this electronic component be mounted using the Surface Mount mounting type. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~85°C for optimal performance. The voltage gain should stay at 110dB. On the buffer amps, there are 1 channels that can be used. In addition to outputting Rail-to-Rail signals, this op amp ic offers a number of other advantages. As a recommendation, this electronic component should be used with a power supply that can deliver 1mA.
MCP6021-I/SN Features
8 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
MCP6021-I/SN Applications
There are a lot of Microchip Technology MCP6021-I/SN Instrumentational OP Amps applications.
- High gain DC amplifier
- Video conversion and routing
- Wireless base stations
- Ultrasound transducers
- Band-pass filter
- Industrial control system
- Signal filtering
- Measurements of Wheatstone bridge
- Medical imaging
- Proportional counter tubes
