MCP6022-E/P
| Parameters | |
|---|---|
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | Not Applicable |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Base Part Number | MCP6022 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Power Supplies | 3/5V |
| Number of Channels | 2 |
| Number of Circuits | 2 |
| Nominal Supply Current | 1mA |
| Output Current | 22mA |
| Slew Rate | 7V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~5.5V |
| Input Offset Voltage (Vos) | 250μV |
| Bandwidth | 10MHz |
| Unity Gain BW-Nom | 10000 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 74dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 500μV |
| Current - Output / Channel | 30mA |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Height | 4.953mm |
| Length | 10.16mm |
| Width | 7.112mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
MCP6022-E/P Overview
In order to protect the op amps, a 8-DIP (0.300, 7.62mm) case is used. Buffer amps of this type are called General Purpose-types. A Tube case is used for delivering the op amp. A total of 8 terminations have been reported in the past few weeks. A total of 8 pins are attached to buffer op amp. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. 8 pins are included on the operational amplifiers. There is an input offset voltage of 250μV for this buffer op amp. For this electrical component, Through Hole is the recommended mounting type. With regard to operating temperature, this op amp functions well at -40°C~125°C. It is a member of the 110dB's 110dB family. On this instrumentation amplifier, there are 2 circuits that are connected together. Op amp ic has 2 channels. In addition to outputting Rail-to-Rail signals, this op amp ic offers a number of other advantages.
MCP6022-E/P Features
8 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
MCP6022-E/P Applications
There are a lot of Microchip Technology MCP6022-E/P Instrumentational OP Amps applications.
- Division circuits
- Integrator circuits
- Communication device
- ECG equipment
- Weighing systems
- Semiconductor detectors
- Radar
- Logarithmic operation circuits
- Scintillation detectors
- Addition operation circuits
