MCP6022-I/ST
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6022 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Number of Elements | 2 |
| Power Supplies | 3/5V |
| Nominal Supply Current | 1mA |
| Output Current | 22mA |
| Current - Supply | 1mA |
| Slew Rate | 7V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~5.5V |
| Output Current per Channel | 30mA |
| Input Offset Voltage (Vos) | 500μV |
| Bandwidth | 10MHz |
| Unity Gain BW-Nom | 10000 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.00015μA |
| Power Supply Rejection Ratio (PSRR) | 74dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Height | 1mm |
| Length | 3mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6022-I/ST Overview
Packaging for the buffer amplifier is in the form of a 8-TSSOP (0.173, 4.40mm Width) case. General Purpose-type instrumentation amplifiers are used in this application. A Tube case is used for delivering the op amp. In recent months, the number of terminations has approached 8. A total of 8 pins are located on this board. Please take in mind that op amp should be run at 5V. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. There are 8 pins on this chip. The input offset voltage is 500μV. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. In relation to the operating temperature of this buffer op amp, it works well at an average of -40°C~85°C . 110dB should be the voltage gain. One of the many advantages that this linear amplifier has, among many other things, is the fact that it outputs Rail-to-Rail signals. As a whole, there are 2 elements that make up this buffer amplifier. In order to ensure optimal performance, an 1mA supply is recommended for this electrical component.
MCP6022-I/ST Features
8 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
MCP6022-I/ST Applications
There are a lot of Microchip Technology MCP6022-I/ST Instrumentational OP Amps applications.
- Fission chambers
- Band-pass filter
- Digital cameras
- Communication
- High input resistance broadband
- Proportional counter tubes
- Logarithmic operation circuits
- Signal filtering
- Test equipment
- Vehicle electronics
