MCP6023-I/P
| Parameters | |
|---|---|
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | Not Applicable |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Base Part Number | MCP6023 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Number of Elements | 1 |
| Power Supplies | 3/5V |
| Operating Supply Current | 1mA |
| Nominal Supply Current | 1mA |
| Output Current | 22mA |
| Slew Rate | 7V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~5.5V |
| Output Current per Channel | 30mA |
| Input Offset Voltage (Vos) | 500μV |
| Bandwidth | 10MHz |
| Unity Gain BW-Nom | 10000 kHz |
| Voltage Gain | 110dB |
| Power Supply Rejection Ratio (PSRR) | 74dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Height | 3.3mm |
| Length | 9.27mm |
| Width | 6.35mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MCP6023-I/P Overview
Packaging for the buffer amplifier is in the form of a 8-DIP (0.300, 7.62mm) case. This is a General Purpose type op amp. Upon delivery, op amp ic is packaged in a Tube case. There is a growing number of terminations approaching the number of 8. Linear amplifier has a total of 8 pins. Please take in mind that this instrumentation amplifier should be run at 5V. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. It has 8 pins that make up the linear amplifier. There is an input offset voltage of 500μV for this buffer op amp. This electronic part is best mounted with type Through Hole. According to the manufacturer, this buffer op amp works well at -40°C~85°C , which is a good operating temperature. As long as the supply current of the chip does not exceed 1mA, this op amp ic can operate. Voltage gain should remain at 110dB. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. The op amp is rated for an operating supply voltage of 1.
MCP6023-I/P Features
8 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
MCP6023-I/P Applications
There are a lot of Microchip Technology MCP6023-I/P Instrumentational OP Amps applications.
- Professional videography
- Polarized electrodes
- Test and measurement instruments
- Displayers for aircraft and air transportation control systems
- Precision measurement
- Strain gauges
- Non-polarized electrodes
- High-frequency data acquisition systems
- Medical instruments
- Blood pressure sensors
