MCP602T-I/ST
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP602 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5.5V |
| Number of Elements | 2 |
| Power Supplies | 3/5V |
| Operating Supply Current | 230μA |
| Nominal Supply Current | 230μA |
| Output Current | 22mA |
| Slew Rate | 2.3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 75 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~6V |
| Output Current per Channel | 22mA |
| Input Offset Voltage (Vos) | 2mV |
| Bandwidth | 2.8MHz |
| Unity Gain BW-Nom | 2800 kHz |
| Voltage Gain | 115dB |
| Average Bias Current-Max (IIB) | 0.00006μA |
| Power Supply Rejection Ratio (PSRR) | 80dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 700μV |
| Low-Bias | YES |
| Micropower | YES |
| Height Seated (Max) | 1.1mm |
| Length | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP602T-I/ST Overview
In the package, you will find a 8-TSSOP (0.173, 4.40mm Width)-case to contain the op amp ic. Op amps are General Purpose types of amplifier on the chip. There is a Tape & Reel (TR) case that is delivered with the instrumentation amplifiers. In recent months, the number of terminations has approached 8. There are a total of 8 pins on this op amp. As a reminder, this buffer op amp should be powered by 5V battery and that the battery should be inserted in the amplifier. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. In total, the buffer amplifier consists of 8 pins. Op amp rates 2mV as input offset voltage. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. In terms of operating temperature, this instrumentation amplifier is well suited to a temperature range of -40°C~85°C. Using a supply current of 230μA , this buffer op amp will be able to operate. There should be no change in the voltage gain. On the output type, there are Rail-to-Rail different types of op amps. There are 2 elements in this buffer amplifier. The operating supply voltage of the buffer op amp is rated at 5.5V. For the packing of the instrumentation amplifier, TAPE AND REEL is adopted.
MCP602T-I/ST Features
8 Pins
supply voltage of 5V
115dB voltage gain
Output Type: Rail-to-Rail
MCP602T-I/ST Applications
There are a lot of Microchip Technology MCP602T-I/ST Instrumentational OP Amps applications.
- Industrial applications including automation
- Portable media players
- Gaming industry
- Industrial control system
- Scintillation detectors
- RF cable systems
- Proportional operation circuits
- Voltage regulation circuit
- Hand-held batteries
- Multimedia playback equipment
