MCP603-E/P
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Base Part Number | MCP603 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5.5V |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Nominal Supply Current | 230μA |
| Output Current | 22mA |
| Slew Rate | 2.3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 75 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~6V |
| Input Offset Voltage (Vos) | 2mV |
| Bandwidth | 2.8MHz |
| Unity Gain BW-Nom | 2800 kHz |
| Voltage Gain | 115dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 80dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 700μV |
| Low-Bias | YES |
| Micropower | YES |
| Max Frequency | 10kHz |
| Programmable Power | NO |
| Height | 4.953mm |
| Length | 10.16mm |
| Width | 7.112mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP603-E/P Overview
Op amp is packaged in 8-DIP (0.300, 7.62mm) case. General Purpose-type instrumentation amplifiers are used in this application. A Tube case is used for delivering the op amp. The number of terminations approaches 8. In this case, there are 8 pins on the board. Please take in mind that this instrumentation amplifier should be run at 5V. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. There are 8 pins on this chip. In terms of input offset voltage, operational amplifier rates 2mV. This electronic part is best mounted with type Through Hole. With regard to operating temperature, this op amp functions well at -40°C~125°C. It is recommended to keep the voltage gain at 115dB at all times. In total, there are 1 circuits on this buffer amplifier. On the buffer amps, there are 1 channels that can be used. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. The operating supply voltage of instrumentation amplifier is rated 5.5V voltage.
MCP603-E/P Features
8 Pins
supply voltage of 5V
115dB voltage gain
Output Type: Rail-to-Rail
MCP603-E/P Applications
There are a lot of Microchip Technology MCP603-E/P Instrumentational OP Amps applications.
- Tablets
- Information processing
- Automation control systems
- Radar
- Video data acquisition
- Switching amplifier
- Medical instruments
- Portable docking station
- Signal operation
- Professional videography
