MCP603-E/SN
| Parameters | |
|---|---|
| Base Part Number | MCP603 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5.5V |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Nominal Supply Current | 230μA |
| Output Current | 22mA |
| Slew Rate | 2.3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 75 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~6V |
| Input Offset Voltage (Vos) | 2mV |
| Bandwidth | 2.8MHz |
| Unity Gain BW-Nom | 2800 kHz |
| Voltage Gain | 115dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 80dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 700μV |
| Low-Bias | YES |
| Micropower | YES |
| Max Frequency | 10kHz |
| Programmable Power | NO |
| Height | 1.5mm |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
MCP603-E/SN Overview
There is a 8-SOIC (0.154, 3.90mm Width) case in which the instrumentation amplifier is packaged. This is a General Purpose type op amp. It comes in a Tube case, which protects instrumentation amplifier from damage during delivery. During the past two weeks, there have been close to 8 terminations. There are a total of 8 pins on this op amp. I would like to remind you that this buffer op amp should be powered by an 5V battery. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. Linear amplifier includes 8 pins. Op amp ic rates 2mV for input offset voltage. For this electrical component, Surface Mount is the recommended mounting type. The buffer amplifier functions well at -40°C~125°C as far as operating temperature is concerned. Voltage gain should remain at 115dB. On this buffer amplifier, there are 1 circuits. 1 channels are available on the instrumentation amplifier. As one of the many benefits of this buffer amplifier, it puts out Rail-to-Rail signals, which is one of the many benefits it offers. The operating supply voltage of the buffer op amp is rated at 5.5V.
MCP603-E/SN Features
8 Pins
supply voltage of 5V
115dB voltage gain
Output Type: Rail-to-Rail
MCP603-E/SN Applications
There are a lot of Microchip Technology MCP603-E/SN Instrumentational OP Amps applications.
- RF cable systems
- Biopotential
- Signal filtering
- Cinema or auditorium audio system
- High speed sample
- Integrator circuits
- Thermocouples
- Car stereo
- Signal transformation
- Proportional operation circuits
