MCP603-I/SN
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP603 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5.5V |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Operating Supply Current | 230μA |
| Nominal Supply Current | 230μA |
| Output Current | 22mA |
| Slew Rate | 2.3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 75 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~6V |
| Output Current per Channel | 22mA |
| Input Offset Voltage (Vos) | 2mV |
| Bandwidth | 2.8MHz |
| Unity Gain BW-Nom | 2800 kHz |
| Voltage Gain | 115dB |
| Average Bias Current-Max (IIB) | 0.00006μA |
| Power Supply Rejection Ratio (PSRR) | 80dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 700μV |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Length | 4.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP603-I/SN Overview
Packaging for the buffer amplifier is in the form of a 8-SOIC (0.154, 3.90mm Width) case. The instrumentation amplifier in this picture is of the General Purpose-type. The op amp is delivered to you in a Tube case. It is estimated that there will be 8 terminations in the next few months. A total of 8 pins are attached to buffer op amp. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. It has 8 pins that make up the linear amplifier. Op amp rates 2mV as input offset voltage. Surface Mount is the recommended mounting type of operational amplifiers. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~85°C for optimal performance. You can run this op amp ic on 230μA . Keeping the voltage gain at 115dB is the best course of action. There are 1 channels on the operational amplifiers. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages. The operating supply voltage of instrumentation amplifier is rated 5.5V voltage.
MCP603-I/SN Features
8 Pins
supply voltage of 5V
115dB voltage gain
Output Type: Rail-to-Rail
MCP603-I/SN Applications
There are a lot of Microchip Technology MCP603-I/SN Instrumentational OP Amps applications.
- Automation control systems
- Portable electronic products powered by batteries
- Micro signal measurement
- Non-polarized electrodes
- Wireless base stations
- Semiconductor detectors
- Power transmission
- Medical imaging
- Digital cameras
- Hand-held batteries
