MCP6031-E/MS
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2004 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.8V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6031 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Power Supplies | 2/5V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Nominal Supply Current | 900nA |
| Output Current | 23mA |
| Slew Rate | 0.004V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~5.5V |
| Input Offset Voltage (Vos) | 150μV |
| Bandwidth | 10 kHz |
| Unity Gain BW-Nom | 10000 kHz |
| Voltage Gain | 115dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Max Frequency | 1kHz |
| Programmable Power | NO |
| Height | 950μm |
| Length | 3mm |
| Width | 3mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6031-E/MS Overview
In the package, you will find a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)-case to contain the op amp ic. General Purpose-type instrumentation amplifiers are used in this application. It comes in a Tube case, which protects instrumentation amplifier from damage during delivery. It is estimated that there will be 8 terminations in the next few months. Buffer amplifier has a total of 8 pins. As a reminder, this buffer op amp should be powered by 1.8V battery and that the battery should be inserted in the amplifier. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. In total, the buffer amplifier consists of 8 pins. As far as the input offset voltage is concerned, linear amplifier rates at 150μV. It is recommended that this electronic component be mounted using the Surface Mount mounting type. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~125°C for optimal performance. Voltage gain should remain at 115dB. This op amp ic has 1 circuits. On the buffer amps, there are 1 channels that can be used. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages.
MCP6031-E/MS Features
8 Pins
supply voltage of 1.8V
115dB voltage gain
Output Type: Rail-to-Rail
MCP6031-E/MS Applications
There are a lot of Microchip Technology MCP6031-E/MS Instrumentational OP Amps applications.
- Inverse/same-phase proportional circuit
- Switching amplifier
- Precision measurement
- Blood pressure sensors
- Industrial control system
- Power generator
- High/low-pass filter circuit
- Communication device
- Band-pass filter
- Band-stop filter
