MCP6034-E/ST
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2000 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 1.8V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6034 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Power Supplies | 2/5V |
| Number of Channels | 4 |
| Operating Supply Current | 900nA |
| Nominal Supply Current | 900nA |
| Output Current | 23mA |
| Slew Rate | 0.004V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~5.5V |
| Output Current per Channel | 23mA |
| Input Offset Voltage (Vos) | 150μV |
| Bandwidth | 10 kHz |
| Unity Gain BW-Nom | 10000 kHz |
| Voltage Gain | 115dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Max Frequency | 1kHz |
| Bias Current-Max (IIB) @25C | 0.0001μA |
| Programmable Power | NO |
| Height | 1.5mm |
| Length | 8.65mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6034-E/ST Overview
Op amp is packaged in 14-TSSOP (0.173, 4.40mm Width) case. The instrumentation amplifier in this picture is of the General Purpose-type. The case in which buffer amplifier is delivered is called a Tube case. The number of terminations approaches 14. It consists of a total of 14 pins in total. Please take in mind that op amp should be run at 1.8V. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. An 14-pin op amp ic is included in the package. As far as the input offset voltage is concerned, linear amplifier rates at 150μV. For this electrical component, Surface Mount is the recommended mounting type. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureYou can run this op amp ic on 900nA . The voltage gain should stay at 115dB. There are a total of 4 channels available on the op amps. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals.
MCP6034-E/ST Features
14 Pins
supply voltage of 1.8V
115dB voltage gain
Output Type: Rail-to-Rail
MCP6034-E/ST Applications
There are a lot of Microchip Technology MCP6034-E/ST Instrumentational OP Amps applications.
- Oscilloscopes
- Exponential operation circuits
- Ultrasound transducers
- Video amplifiers
- Weighing systems
- Television
- Fission chambers
- Fast A/D and D/A converters
- Portable media players
- Power generator
