MCP603T-E/CH
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 |
| Number of Pins | 6 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.95mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP603 |
| Pin Count | 6 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5.5V |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Nominal Supply Current | 230μA |
| Output Current | 22mA |
| Slew Rate | 2.3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 75 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~6V |
| Input Offset Voltage (Vos) | 2mV |
| Bandwidth | 2.8MHz |
| Unity Gain BW-Nom | 2800 kHz |
| Voltage Gain | 115dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 80dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 700μV |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Height | 1.3mm |
| Length | 3.1mm |
| Width | 1.8mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP603T-E/CH Overview
There is a SOT-23-6 case in which the instrumentation amplifier is packaged. General Purpose-type instrumentation amplifiers are used in this application. Linear amplifier is delivered in a Tape & Reel (TR) case. A total of 6 terminations have been reported in the past few weeks. It consists of a total of 6 pins in total. This linear amplifier should be powered by an 5V battery. In order to be more specific, this instrumentation amplifier is one of the types of Operational Amplifier devices. Linear amplifier includes 6 pins. Regarding input offset voltage, op amp rates 2mV. For this electrical component, Surface Mount is the recommended mounting type. The buffer amplifier functions well at -40°C~125°C as far as operating temperature is concerned. You should keep the voltage gain at 115dB for the time being. A linear amplifier like this has 1 circuits on it. The op amp ic has 1 channels on it. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. The operating supply voltage of the buffer op amp is rated at 5.5V. TAPE AND REEL is adopted to pack the instrumentation amplifier.
MCP603T-E/CH Features
6 Pins
supply voltage of 5V
115dB voltage gain
Output Type: Rail-to-Rail
MCP603T-E/CH Applications
There are a lot of Microchip Technology MCP603T-E/CH Instrumentational OP Amps applications.
- Hand-held batteries
- Inverse/same-phase proportional circuit
- Multiplication circuits
- Weak signal detection
- Signal filtering
- Computer workstations
- Communication device
- Car stereo
- Scintillation detectors
- Logarithmic operation circuits
