MCP604-E/P
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Base Part Number | MCP604 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5.5V |
| Power Supplies | 3/5V |
| Number of Channels | 4 |
| Number of Circuits | 4 |
| Nominal Supply Current | 230μA |
| Output Current | 22mA |
| Slew Rate | 2.3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 75 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~6V |
| Input Offset Voltage (Vos) | 2mV |
| Bandwidth | 2.8MHz |
| Unity Gain BW-Nom | 2800 kHz |
| Voltage Gain | 115dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 80dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 700μV |
| Low-Bias | YES |
| Micropower | YES |
| Height | 4.953mm |
| Length | 19.69mm |
| Width | 7.112mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP604-E/P Overview
The linear amplifier is packaged in a 14-DIP (0.300, 7.62mm) case. Buffer amps of this type are called General Purpose-types. It comes in a Tube case, which protects instrumentation amplifier from damage during delivery. A total of 14 terminations have been reported in the past few weeks. Buffer amplifier has a total of 14 pins. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. A total of 14 pins are present on the instrumentation amplifier. Regarding input offset voltage, buffer amplifier rates 2mV voltage. For this electrical component, the recommended mounting type is Through Hole, which is the most common. With regard to operating temperature, this op amp functions well at -40°C~125°C. Voltage gain should remain at 115dB. On this buffer amplifier, there are 4 circuits. 4 channels are available on the instrumentation amplifier. One of its many advantages is that buffer op amp outputs Rail-to-Rail signals. The operating supply voltage of instrumentation amplifier is rated 5.5V voltage.
MCP604-E/P Features
14 Pins
supply voltage of 5V
115dB voltage gain
Output Type: Rail-to-Rail
MCP604-E/P Applications
There are a lot of Microchip Technology MCP604-E/P Instrumentational OP Amps applications.
- Large motor controllers
- Medical instruments
- RF cable systems
- Digital cameras
- Portable docking station
- Portable electronic products powered by batteries
- High-frequency data acquisition systems
- Blood pressure sensors
- Medical imaging
- Radar
