MCP6041-I/MS
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2000 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6041 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5.5V |
| Number of Elements | 1 |
| Operating Supply Current | 600nA |
| Nominal Supply Current | 600nA |
| Output Current | 21mA |
| Slew Rate | 0.003V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.4V~6V |
| Output Current per Channel | 20mA |
| Input Offset Voltage (Vos) | 3mV |
| Gain Bandwidth Product | 14kHz |
| Unity Gain BW-Nom | 14 kHz |
| Voltage Gain | 115dB |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Wideband | NO |
| Height | 850μm |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6041-I/MS Overview
Packaging for the buffer amplifier is in the form of a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case. There are two types of operational amplifiers in this circuit. The op amp is delivered to you in a Tube case. A total of 8 terminations have been reported in the past few weeks. In total, there are 8 pins on this op amp ic. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. This particular linear amplifier is a type of Operational Amplifier device, to be precise. 8 pins are located on the operational amplifiers. There is an input offset voltage of 3mV for this buffer op amp. This electronic part is recommended for mounting type Surface Mount. According to the manufacturer, this buffer op amp works well at -40°C~85°C , which is a good operating temperature. Operational amplifier can operate supply current at 600nA. 115dB should be the voltage gain. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. Op amp has total of 1 elements. The operating supply voltage of instrumentation amplifier is rated 5.5V voltage.
MCP6041-I/MS Features
8 Pins
supply voltage of 5V
115dB voltage gain
Output Type: Rail-to-Rail
MCP6041-I/MS Applications
There are a lot of Microchip Technology MCP6041-I/MS Instrumentational OP Amps applications.
- Test and measurement instruments
- Gaming industry
- Multiplication circuits
- High input resistance broadband
- RF cable systems
- Video computer boards
- Precision measurement
- Industrial control system
- Proportional operation circuits
- Radiation thermometry transducers
