MCP6042-E/P
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2004 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | MCP6042 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5.5V |
| Power Supplies | 1.5/5V |
| Number of Channels | 2 |
| Nominal Supply Current | 600nA |
| Output Current | 21mA |
| Current - Supply | 600nA |
| Slew Rate | 0.003V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.4V~6V |
| Input Offset Voltage (Vos) | 3mV |
| Bandwidth | 14 kHz |
| Unity Gain BW-Nom | 14 kHz |
| Voltage Gain | 115dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Height | 1.25mm |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6042-E/P Overview
Packaging for the buffer amplifier is in the form of a 8-DIP (0.300, 7.62mm) case. A General Purpose-type buffer amplifier is shown here. A Tube case is used to deliver the buffer op amp. The number of terminations is approaching the 8 mark. A total of 8 pins are located on this board. The linear amplifier should be run at 5V at all times, so please keep that in mind when using it. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. The op amp ic has an array of 8 pins on it. Regarding input offset voltage, buffer amplifier rates 3mV voltage. Through Hole is the recommended mounting type for this linear amplifier. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureIt is a member of the 115dB's 115dB family. The op amp ic has 2 channels on it. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages. The operating supply voltage of the buffer op amp is rated at 5.5V. A supply of 600nA or higher is recommended for use with this electronic part.
MCP6042-E/P Features
8 Pins
supply voltage of 5V
115dB voltage gain
Output Type: Rail-to-Rail
MCP6042-E/P Applications
There are a lot of Microchip Technology MCP6042-E/P Instrumentational OP Amps applications.
- Integrator circuits
- Precision measurement
- Polarized electrodes
- Radiation thermometry transducers
- Strain gauges
- Signal amplification
- Car stereo
- Power generator
- Logarithmic operation circuits
- Medical imaging
