MCP6042-I/MS
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2004 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6042 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5.5V |
| Number of Elements | 2 |
| Power Supplies | 1.5/5V |
| Operating Supply Current | 600nA |
| Nominal Supply Current | 600nA |
| Output Current | 21mA |
| Slew Rate | 0.003V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.4V~6V |
| Output Current per Channel | 20mA |
| Input Offset Voltage (Vos) | 3mV |
| Bandwidth | 14 kHz |
| Unity Gain BW-Nom | 14 kHz |
| Voltage Gain | 115dB |
| Average Bias Current-Max (IIB) | 0.0001μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Height | 939.8μm |
| Length | 2.9972mm |
| Width | 2.9972mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6042-I/MS Overview
Packaging for the buffer amplifier is in the form of a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case. General Purpose-type instrumentation amplifiers are used in this application. As far as the packaging is concerned, buffer op amp is delivered in a Tube case. There have been a total of 8 terminations over the past year. A total of 8 pins are located on this board. It is important to remember that this op amp should be operated at a voltage of 5V volts. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. An 8-pin op amp ic is included in the package. With regards to the offset voltage of the input, buffer amplifier is rated at 3mV. This electronic part is best mounted with type Surface Mount. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~85°C for optimal performance. The buffer amplifier is capable of operating from a supply current of 600nA . Voltage gain should remain at 115dB. Buffer amplifier produces Rail-to-Rail signals, which is one of its many benefits. As a whole, there are 2 elements that make up this buffer amplifier. The operating supply voltage of the buffer op amp is rated at 5.5V.
MCP6042-I/MS Features
8 Pins
supply voltage of 5V
115dB voltage gain
Output Type: Rail-to-Rail
MCP6042-I/MS Applications
There are a lot of Microchip Technology MCP6042-I/MS Instrumentational OP Amps applications.
- Subtraction operation circuits
- Communication
- Computer workstations
- Active probe
- Signal filtering
- Video conversion and routing
- Fission chambers
- Large motor controllers
- High gain DC amplifier
- Strain gauges
