MCP6042-I/SN
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2013 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6042 |
| Pin Count | 8 |
| Lead Pitch | 1.27mm |
| Output Type | Rail-to-Rail |
| Max Output Current | 30mA |
| Operating Supply Voltage | 5.5V |
| Power Supplies | 1.5/5V |
| Row Spacing | 6.02 mm |
| Number of Channels | 2 |
| Number of Circuits | 2 |
| Nominal Supply Current | 600nA |
| Output Current | 21mA |
| Max Supply Current | 2mA |
| Min Input Voltage | 1.4V |
| Slew Rate | 0.003V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 1pA |
| Max Input Voltage | 6V |
| Voltage - Supply, Single/Dual (±) | 1.4V~6V |
| Input Offset Voltage (Vos) | 3mV |
| Bandwidth | 14 kHz |
| Unity Gain BW-Nom | 14 kHz |
| Voltage Gain | 115dB |
| Average Bias Current-Max (IIB) | 0.0001μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Current - Output / Channel | 20mA |
| Low-Bias | YES |
| Micropower | YES |
| Max Frequency | 1kHz |
| Height | 1.25mm |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6042-I/SN Overview
A 8-SOIC (0.154, 3.90mm Width) case is used to package the op amp. An op amp ic of the General Purpose type. As far as the packaging is concerned, buffer op amp is delivered in a Tube case. During the past two weeks, there have been close to 8 terminations. In this case, there are 8 pins on the board. I would like to remind you that this buffer op amp should be powered by an 5V battery. It should be noted that this op amp is a type of Operational Amplifier device. 8 pins are located on the operational amplifiers. With regard to input offset voltage, instrumentation amplifier is rated at 3mV. For this electronic part, it is recommended that you mount it with type Surface Mount. With regard to operating temperature, this op amp functions well at -40°C~85°C. Op amp is a member of the 115dB's 115dB family. On this instrumentation amplifier, there are 2 circuits that are connected together. There are 2 channels on the operational amplifiers. One of the many advantages that this linear amplifier has, among many other things, is the fact that it outputs Rail-to-Rail signals. The operating supply voltage of instrumentation amplifier is rated 5.5V voltage.
MCP6042-I/SN Features
8 Pins
supply voltage of 5V
115dB voltage gain
Output Type: Rail-to-Rail
MCP6042-I/SN Applications
There are a lot of Microchip Technology MCP6042-I/SN Instrumentational OP Amps applications.
- Fast A/D and D/A converters
- Micro signal measurement
- Mobile phone
- Displayers for aircraft and air transportation control systems
- Oscilloscopes
- Exponential operation circuits
- Video data acquisition
- Medical instruments
- Gaming industry
- Radar
