MCP6043-E/MS
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2004 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6043 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5.5V |
| Number of Channels | 1 |
| Operating Supply Current | 600nA |
| Nominal Supply Current | 600nA |
| Output Current | 21mA |
| Slew Rate | 0.003V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.4V~6V |
| Output Current per Channel | 20mA |
| Input Offset Voltage (Vos) | 3mV |
| Bandwidth | 14 kHz |
| Unity Gain BW-Nom | 14 kHz |
| Voltage Gain | 115dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Height | 950μm |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6043-E/MS Overview
It is packaged in an 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)-case that protects the operational amplifiers from damage. An op amp ic of the General Purpose type. Instrumentation amplifier is delivered in a Tube case. The number of terminations approaches 8. Buffer amplifier has a total of 8 pins on it. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. In order to be more specific, this instrumentation amplifier is one of the types of Operational Amplifier devices. There are 8 pins on this chip. Regarding input offset voltage, op amp rates 3mV. For this electrical component, Surface Mount is the recommended mounting type. In relation to the operating temperature of this buffer op amp, it works well at an average of -40°C~125°C . Operational amplifier can operate supply current at 600nA. Voltage gain should remain at 115dB. Instrumentation amplifier has 1 channels on it. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages. The operating supply voltage of the buffer op amp is rated at 5.5V.
MCP6043-E/MS Features
8 Pins
supply voltage of 5V
115dB voltage gain
Output Type: Rail-to-Rail
MCP6043-E/MS Applications
There are a lot of Microchip Technology MCP6043-E/MS Instrumentational OP Amps applications.
- Signal amplification
- Information processing
- Tablets
- MP3
- Semiconductor detectors
- Weak signal detection
- Cinema or auditorium audio system
- Voltage regulation circuit
- Precision measurement
- Vehicle electronics
