MCP6043-E/P
| Parameters | |
|---|---|
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Base Part Number | MCP6043 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5.5V |
| Number of Channels | 1 |
| Operating Supply Current | 600nA |
| Nominal Supply Current | 600nA |
| Output Current | 21mA |
| Slew Rate | 0.003V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.4V~6V |
| Output Current per Channel | 20mA |
| Input Offset Voltage (Vos) | 3mV |
| Bandwidth | 14 kHz |
| Unity Gain BW-Nom | 14 kHz |
| Voltage Gain | 115dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Height | 4.953mm |
| Length | 10.16mm |
| Width | 7.112mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2002 |
MCP6043-E/P Overview
It is packaged in an 8-DIP (0.300, 7.62mm)-case that protects the operational amplifiers from damage. There are two types of operational amplifiers in this circuit. It comes in a Tube case, which protects instrumentation amplifier from damage during delivery. A total of 8 terminations have been reported in the past few weeks. A total of 8 pins are attached to buffer op amp. I would like to remind you that this buffer op amp should be powered by an 5V battery. Instrumentation amplifier is a part of Operational Amplifier. In total, the buffer amplifier consists of 8 pins. With regard to input offset voltage, instrumentation amplifier is rated at 3mV. This electronic part is best mounted with type Through Hole. In terms of operating temperature, this instrumentation amplifier is well suited to a temperature range of -40°C~125°C. You can run this op amp ic on 600nA . Voltage gain should remain at 115dB. Buffer op amp is equipped with 1 channels on the device. One of the many advantages that this linear amplifier has, among many other things, is the fact that it outputs Rail-to-Rail signals. The operating supply voltage of the buffer op amp is rated at 5.5V.
MCP6043-E/P Features
8 Pins
supply voltage of 5V
115dB voltage gain
Output Type: Rail-to-Rail
MCP6043-E/P Applications
There are a lot of Microchip Technology MCP6043-E/P Instrumentational OP Amps applications.
- Hand-held batteries
- Active probe
- Polarized electrodes
- MP3
- Signal amplification
- Integrator circuits
- Communication device
- Signal filtering
- Communication
- Portable media players
