MCP6043-I/P
| Parameters | |
|---|---|
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5.5V |
| Number of Channels | 1 |
| Operating Supply Current | 600nA |
| Nominal Supply Current | 600nA |
| Output Current | 21mA |
| Slew Rate | 0.003V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.4V~6V |
| Output Current per Channel | 20mA |
| Input Offset Voltage (Vos) | 3mV |
| Bandwidth | 14 kHz |
| Unity Gain BW-Nom | 14 kHz |
| Voltage Gain | 115dB |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Height | 3.3mm |
| Length | 9.27mm |
| Width | 6.35mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2008 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Base Part Number | MCP6043 |
MCP6043-I/P Overview
In order to protect the op amps, a 8-DIP (0.300, 7.62mm) case is used. An op amp of this type is a General Purpose-type. Linear amplifier is delivered in a Tube case. A total of 8 terminations have been reported in the past few weeks. A total of 8 pins are attached to buffer op amp. The linear amplifier should be run at 5V at all times, so please keep that in mind when using it. It should be noted that this op amp is a type of Operational Amplifier device. The op amp ic has an array of 8 pins on it. With regards to the offset voltage of the input, buffer amplifier is rated at 3mV. This electrical part should be mounted using type Through Hole. Regarding the operating temperature of this device, instrumentation amplifier performs well at a temperature of -40°C~85°C . As long as the supply current of the chip does not exceed 600nA, this op amp ic can operate. The voltage gain should stay at 115dB. There are a total of 1 channels available on the op amps. This op amp ic outputs Rail-to-Rail signals, which is one of the many benefits it has. The operating supply voltage of the buffer op amp is rated at 5.5V.
MCP6043-I/P Features
8 Pins
supply voltage of 5V
115dB voltage gain
Output Type: Rail-to-Rail
MCP6043-I/P Applications
There are a lot of Microchip Technology MCP6043-I/P Instrumentational OP Amps applications.
- Automotive sensors
- Hand-held batteries
- Vehicle electronics
- Medical imaging
- Displayers for aircraft and air transportation control systems
- High input resistance broadband
- Thermocouples
- ECG equipment
- Professional videography
- Proportional counter tubes
