MCP6043T-I/MS
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6043 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5.5V |
| Number of Elements | 1 |
| Nominal Supply Current | 600nA |
| Output Current | 21mA |
| Current - Supply | 600nA |
| Slew Rate | 0.003V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.4V~6V |
| Input Offset Voltage (Vos) | 3mV |
| Gain Bandwidth Product | 14kHz |
| Unity Gain BW-Nom | 14 kHz |
| Voltage Gain | 115dB |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Current - Output / Channel | 20mA |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Wideband | NO |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MCP6043T-I/MS Overview
The linear amplifier is packaged in a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case which makes it easy for the consumer to handle. Op amps are General Purpose types of amplifier on the chip. A Tape & Reel (TR) case is used for delivering the op amp. The number of terminations approaches 8. A total of 8 pins are attached to buffer op amp. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. This particular linear amplifier is a type of Operational Amplifier device, to be precise. 8 pins are located on the operational amplifiers. The input offset voltage is 3mV. This electronic component is recommended to be mounted using the mounting type Surface Mount. It is important to note that this linear amplifier works well at a temperature of -40°C~85°C when it comes to operating temperature115dB should remain the voltage gain. In addition to outputting Rail-to-Rail signals, this op amp ic offers a number of other advantages. Op amp has total of 1 elements. The operating supply voltage of instrumentation amplifier is rated 5.5V voltage. To pack the operational amplifier ics, TAPE AND REEL is adopted as the packing method. We recommend that you use this electronic part with an 600nA supply in order to get the best performance from it.
MCP6043T-I/MS Features
8 Pins
supply voltage of 5V
115dB voltage gain
Output Type: Rail-to-Rail
MCP6043T-I/MS Applications
There are a lot of Microchip Technology MCP6043T-I/MS Instrumentational OP Amps applications.
- Voltage regulation circuit
- High gain DC amplifier
- Professional videography
- Image computer boards
- single/dual op amp sum and difference circuits
- Laptop
- Switching amplifier
- Weak signal detection
- Power transmission
- Test equipment
