MCP6044-E/P
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2008 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | Not Applicable |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | MCP6044 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5.5V |
| Power Supplies | 1.5/5V |
| Number of Channels | 4 |
| Operating Supply Current | 600nA |
| Nominal Supply Current | 600nA |
| Output Current | 21mA |
| Slew Rate | 0.003V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.4V~6V |
| Output Current per Channel | 20mA |
| Input Offset Voltage (Vos) | 3mV |
| Bandwidth | 14 kHz |
| Unity Gain BW-Nom | 14 kHz |
| Voltage Gain | 115dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Height | 4.953mm |
| Length | 19.69mm |
| Width | 7.112mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6044-E/P Overview
There is a 14-DIP (0.300, 7.62mm) case package that contains the instrumentation amplifiers. An op amp ic of the General Purpose type. Instrumentation amplifier is delivered in a Tube case. In recent months, the number of terminations has approached 14. The pins on this board total to 14 in total. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. To be specific, this instrumentation amplifier is a type of Operational Amplifier. In total, the buffer amplifier consists of 14 pins. There is an input offset voltage of 3mV for this buffer op amp. Through Hole is the recommended mounting type for this linear amplifier. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureIn order for this instrumentation amplifier to operate, the supply current needs to be between 600nA and 10 . It is recommended to keep the voltage gain at 115dB at all times. 4 channels are available on the instrumentation amplifier. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages. The operating supply voltage of instrumentation amplifier is rated 5.5V voltage.
MCP6044-E/P Features
14 Pins
supply voltage of 5V
115dB voltage gain
Output Type: Rail-to-Rail
MCP6044-E/P Applications
There are a lot of Microchip Technology MCP6044-E/P Instrumentational OP Amps applications.
- Biopotential
- Signal amplification
- Cinema or auditorium audio system
- Signal operation
- Image computer boards
- Mobile phone
- PDA
- Polarized electrodes
- Measurements of Wheatstone bridge
- Non-polarized electrodes
