MCP6044-E/ST
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Supplier Device Package | 14-TSSOP |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2008 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -40°C |
| Base Part Number | MCP6044 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5.5V |
| Number of Elements | 4 |
| Number of Channels | 4 |
| Number of Circuits | 4 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 1.4V |
| Operating Supply Current | 600nA |
| Nominal Supply Current | 600nA |
| Output Current | 21mA |
| Current - Supply | 600nA |
| Slew Rate | 0.003V/μs |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.4V~6V |
| Output Current per Channel | 20mA |
| Input Offset Voltage (Vos) | 3mV |
| Bandwidth | 14 kHz |
| Gain Bandwidth Product | 14kHz |
| Voltage Gain | 115dB |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Voltage - Input Offset | 3mV |
| Number of Amplifiers | 4 |
| Height | 1.05mm |
| Length | 5.1mm |
| Width | 4.5mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6044-E/ST Overview
Packaging for the buffer amplifier is in the form of a 14-TSSOP (0.173, 4.40mm Width) case. Buffer amps of this type are called General Purpose-types. It comes in a Tube case, which protects instrumentation amplifier from damage during delivery. An 14-pin op amp ic is included in the package. Regarding input offset voltage, op amp rates 3mV. This electronic part is recommended for mounting type Surface Mount. With regard to operating temperature, this op amp functions well at -40°C~125°C. It is possible to operate this buffer amplifier from a supply current of 600nA . Maintain 115dB as the voltage gain. A instrumentation amplifier like this has 4 circuits. As far as the device is concerned, buffer amplifier has 4 channels. One of the many benefits of this op amp ic is that it emits Rail-to-Rail signals. The temperature should not be lower than -40°C for operational amplifier ics to operate. You should not use op amp above 125°C degrees. There are 4 elements in total in this linear amplifier. The operating supply voltage of instrumentation amplifier is rated 5.5V voltage. For optimal performance, this electrical part should be connected to a supply with a current of 600nA. This electric component can work from a voltage of under 6V as far as supply voltage is concerned. As a general rule, it is advisable to keep the op amp's supply voltage above 1.4V at all times. In total, there are 4 op amps on the device.
MCP6044-E/ST Features
115dB voltage gain
Output Type: Rail-to-Rail
MCP6044-E/ST Applications
There are a lot of Microchip Technology MCP6044-E/ST Instrumentational OP Amps applications.
- Logarithmic operation circuits
- Active probe
- Integrator circuits
- Subtraction operation circuits
- Addition operation circuits
- Signal transformation
- Blood pressure sensors
- Industrial applications including automation
- Inverse/same-phase proportional circuit
- High/low-pass filter circuit
