MCP6044-I/ST
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2000 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6044 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5.5V |
| Number of Elements | 4 |
| Power Supplies | 1.5/5V |
| Nominal Supply Current | 600nA |
| Output Current | 21mA |
| Current - Supply | 600nA |
| Slew Rate | 0.003V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.4V~6V |
| Input Offset Voltage (Vos) | 3mV |
| Bandwidth | 14 kHz |
| Unity Gain BW-Nom | 14 kHz |
| Voltage Gain | 115dB |
| Average Bias Current-Max (IIB) | 0.0001μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Current - Output / Channel | 20mA |
| Low-Bias | YES |
| Micropower | YES |
| Height | 900μm |
| Length | 5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6044-I/ST Overview
In the package, you will find a 14-TSSOP (0.173, 4.40mm Width)-case to contain the op amp ic. General Purpose-type instrumentation amplifiers are used in this application. As far as the packaging is concerned, buffer op amp is delivered in a Tube case. The number of terminations is approaching the 14 mark. Buffer amplifier has a total of 14 pins. This linear amplifier should be powered by an 5V battery. It should be noted that this op amp is a type of Operational Amplifier device. There are 14 pins on this chip. In terms of the input offset voltage, instrumentation amplifier rates at 3mV. It is recommended that this electronic component be mounted using the Surface Mount mounting type. In terms of operating temperatures, this buffer amplifier works very well at a temperature of around -40°C~85°C . You should keep the voltage gain at 115dB for the time being. As one of the many benefits of this buffer amplifier, it puts out Rail-to-Rail signals, which is one of the many benefits it offers. There is a rating of 4 for the operating supply voltage of the buffer op amp. The operating supply voltage of instrumentation amplifier is rated 5.5V voltage. To run supply current of buffer amplifier under 600nA.
MCP6044-I/ST Features
14 Pins
supply voltage of 5V
115dB voltage gain
Output Type: Rail-to-Rail
MCP6044-I/ST Applications
There are a lot of Microchip Technology MCP6044-I/ST Instrumentational OP Amps applications.
- RF cable systems
- Displayers for aircraft and air transportation control systems
- Thermocouples
- Hand-held batteries
- Non-polarized electrodes
- High-frequency data acquisition systems
- Mobile phone
- High input resistance broadband
- Broadcasting
- Large motor controllers
