MCP6044T-E/SL
| Parameters | |
|---|---|
| Unity Gain BW-Nom | 14 kHz |
| Voltage Gain | 115dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Height Seated (Max) | 1.75mm |
| Length | 8.65mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6044 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5.5V |
| Number of Elements | 4 |
| Power Supplies | 1.5/5V |
| Nominal Supply Current | 600nA |
| Output Current | 21mA |
| Current - Supply | 600nA |
| Slew Rate | 0.003V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.4V~6V |
| Input Offset Voltage (Vos) | 3mV |
| Gain Bandwidth Product | 14kHz |
MCP6044T-E/SL Overview
In order to protect the op amps, a 14-SOIC (0.154, 3.90mm Width) case is used. General Purpose-type instrumentation amplifiers are used in this application. It comes in a Tape & Reel (TR) case, which protects instrumentation amplifier from damage during delivery. It is estimated that there will be at least 14 terminations this year. The pins on this board total to 14 in total. This linear amplifier should be powered by an 5V battery. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. 14 pins are available on the instrumentation amplifier. With regards to the offset voltage of the input, buffer amplifier is rated at 3mV. For this electronic part, it is recommended that you mount it with type Surface Mount. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~125°C for optimal performance. There should be no change in the voltage gain. This op amp ic outputs Rail-to-Rail signals, which is one of the many benefits it has. It is possible to count 4 elements on this buffer amplifier. The operating supply voltage of the buffer op amp is rated at 5.5V. TAPE AND REEL is adopted to pack the instrumentation amplifier. For optimal performance, this electrical part should be connected to a supply with a current of 600nA.
MCP6044T-E/SL Features
14 Pins
supply voltage of 5V
115dB voltage gain
Output Type: Rail-to-Rail
MCP6044T-E/SL Applications
There are a lot of Microchip Technology MCP6044T-E/SL Instrumentational OP Amps applications.
- Instrumentation
- ECG equipment
- Signal operation
- Automatic control
- Band-pass filter
- Division circuits
- Thermocouples
- Subtraction operation circuits
- PDA
- Signal amplification
