MCP604T-I/SL
| Parameters | |
|---|---|
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP604 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5.5V |
| Number of Elements | 4 |
| Power Supplies | 3/5V |
| Operating Supply Current | 230μA |
| Nominal Supply Current | 230μA |
| Output Current | 22mA |
| Slew Rate | 2.3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 75 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~6V |
| Output Current per Channel | 22mA |
| Input Offset Voltage (Vos) | 2mV |
| Bandwidth | 2.8MHz |
| Unity Gain BW-Nom | 2800 kHz |
| Voltage Gain | 115dB |
| Average Bias Current-Max (IIB) | 0.00006μA |
| Power Supply Rejection Ratio (PSRR) | 80dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 700μV |
| Low-Bias | YES |
| Micropower | YES |
| Height Seated (Max) | 1.75mm |
| Length | 8.69mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Published | 2000 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
MCP604T-I/SL Overview
There is a 14-SOIC (0.154, 3.90mm Width) case in which the instrumentation amplifier is packaged. General Purpose-type instrumentation amplifiers are used in this application. It comes in a Tape & Reel (TR) case, which protects instrumentation amplifier from damage during delivery. There have been a total of 14 terminations over the past year. A total of 14 pins are located on this board. I would like to remind you that this buffer op amp should be powered by an 5V battery. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. There are 14 pins on this chip. As far as the input offset voltage is concerned, linear amplifier rates at 2mV. This electronic component is recommended to be mounted using the mounting type Surface Mount. Regarding the operating temperature of this device, instrumentation amplifier performs well at a temperature of -40°C~85°C . Using an 230μA supply current, this operational amplifier ics can be operated. It is a member of the 115dB's 115dB family. As one of the many benefits of this buffer amplifier, it puts out Rail-to-Rail signals, which is one of the many benefits it offers. There are 4 elements in total in this linear amplifier. The operating supply voltage of the buffer op amp is rated at 5.5V. As a result of this, the buffer amplifier is packed in TAPE AND REEL.
MCP604T-I/SL Features
14 Pins
supply voltage of 5V
115dB voltage gain
Output Type: Rail-to-Rail
MCP604T-I/SL Applications
There are a lot of Microchip Technology MCP604T-I/SL Instrumentational OP Amps applications.
- Measurements of Wheatstone bridge
- Automation control systems
- Signal transformation
- Oscilloscopes
- Proportional operation circuits
- MP3
- Commercial audio systems
- Mobile phone
- Power control
- single/dual op amp sum and difference circuits
