MCP6052-E/SN
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2000 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6052 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Number of Channels | 2 |
| Operating Supply Current | 30μA |
| Nominal Supply Current | 30μA |
| Output Current | 26mA |
| Slew Rate | 0.15V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 72 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~6V |
| Output Current per Channel | 26mA |
| Input Offset Voltage (Vos) | 150μV |
| Bandwidth | 385 kHz |
| Unity Gain BW-Nom | 385 kHz |
| Voltage Gain | 115dB |
| Average Bias Current-Max (IIB) | 0.0001μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.0001μA |
| Height | 1.25mm |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6052-E/SN Overview
Packaging for the buffer amplifier is in the form of a 8-SOIC (0.154, 3.90mm Width) case. There are two types of operational amplifiers in this circuit. The op amp is delivered to you in a Tube case. It is estimated that there will be at least 8 terminations this year. The total number of pins on linear amplifier is 8. It would be helpful if you could remember that this op amp ic should be powered by an 3V battery. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. 8 pins are located on the operational amplifiers. Op amp rates 150μV as input offset voltage. Surface Mount is the recommended mounting type of operational amplifiers. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureIt is possible to operate this buffer amplifier from a supply current of 30μA . There should be no change in the voltage gain. Op amp ic has 2 channels. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages.
MCP6052-E/SN Features
8 Pins
supply voltage of 3V
115dB voltage gain
Output Type: Rail-to-Rail
MCP6052-E/SN Applications
There are a lot of Microchip Technology MCP6052-E/SN Instrumentational OP Amps applications.
- Signal amplification
- Exponential operation circuits
- Strain gauges
- Television
- Instrumentation
- Blood pressure sensors
- Biopotential
- Semiconductor detectors
- Portable media players
- High gain DC amplifier
