MCP6054-E/ST
| Parameters | |
|---|---|
| Unity Gain BW-Nom | 385 kHz |
| Voltage Gain | 115dB |
| Average Bias Current-Max (IIB) | 0.0001μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.0001μA |
| Programmable Power | NO |
| Height | 1mm |
| Length | 5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 3V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6054 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Power Supplies | 2/5V |
| Number of Channels | 4 |
| Operating Supply Current | 30μA |
| Nominal Supply Current | 30μA |
| Output Current | 26mA |
| Slew Rate | 0.15V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 72 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~6V |
| Output Current per Channel | 26mA |
| Input Offset Voltage (Vos) | 150μV |
| Bandwidth | 385 kHz |
MCP6054-E/ST Overview
The linear amplifier is packaged in a 14-TSSOP (0.173, 4.40mm Width) case. Op amps are General Purpose types of amplifier on the chip. It comes in a Tube case, which protects instrumentation amplifier from damage during delivery. The number of terminations is approaching the 14 mark. It consists of a total of 14 pins in total. I would like to remind you that this buffer op amp should be powered by an 3V battery. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. An 14-pin op amp ic is included in the package. Op amp ic rates 150μV for input offset voltage. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. In terms of operating temperature, this instrumentation amplifier is well suited to a temperature range of -40°C~125°C. As long as the supply current of the chip does not exceed 30μA, this op amp ic can operate. There should be no change in the voltage gain. The op amp ic has 4 channels on it. A benefit of this op amp ic is that it outputs Rail-to-Rail signals, which is one of the many advantages it has to offer.
MCP6054-E/ST Features
14 Pins
supply voltage of 3V
115dB voltage gain
Output Type: Rail-to-Rail
MCP6054-E/ST Applications
There are a lot of Microchip Technology MCP6054-E/ST Instrumentational OP Amps applications.
- Band-pass filter
- Image computer boards
- MP3
- Inverse/same-phase proportional circuit
- Portable media players
- High/low-pass filter circuit
- Portable docking station
- Professional videography
- Signal filtering
- Polarized electrodes
