MCP6064T-E/ST
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2010 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6064 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Number of Elements | 4 |
| Power Supplies | 2/5V |
| Nominal Supply Current | 60μA |
| Output Current | 27mA |
| Current - Supply | 60μA |
| Slew Rate | 0.25V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 72 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~6V |
| Input Offset Voltage (Vos) | 150μV |
| Gain Bandwidth Product | 730kHz |
| Unity Gain BW-Nom | 730 kHz |
| Voltage Gain | 115dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.0001μA |
| Programmable Power | NO |
| Wideband | NO |
| Height Seated (Max) | 1.2mm |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MCP6064T-E/ST Overview
There is a 14-TSSOP (0.173, 4.40mm Width) case package that contains the instrumentation amplifiers. This is a General Purpose type op amp. A Tape & Reel (TR) case is used to deliver the buffer op amp. The number of terminations approaches 14. A total of 14 pins are attached to buffer op amp. As a reminder, this buffer op amp should be powered by 3V battery and that the battery should be inserted in the amplifier. To be specific, this instrumentation amplifier is a type of Operational Amplifier. In total, the buffer amplifier consists of 14 pins. With regard to input offset voltage, instrumentation amplifier is rated at 150μV. For this electrical component, Surface Mount is the recommended mounting type. According to the manufacturer, this buffer op amp works well at -40°C~125°C , which is a good operating temperature. 115dB should be the voltage gain. In addition to outputting Rail-to-Rail signals, this op amp ic offers a number of other advantages. There are 4 elements in total in this linear amplifier. A TAPE AND REEL-shaped amplifier is used to pack the buffer amps. As a recommendation, this electronic component should be used with a power supply that can deliver 60μA.
MCP6064T-E/ST Features
14 Pins
supply voltage of 3V
115dB voltage gain
Output Type: Rail-to-Rail
MCP6064T-E/ST Applications
There are a lot of Microchip Technology MCP6064T-E/ST Instrumentational OP Amps applications.
- Power transmission
- Portable media players
- High/low-pass filter circuit
- Inverse/same-phase proportional circuit
- MP3
- RF cable systems
- Computer workstations
- Logarithmic operation circuits
- Communication
- Radar
