MCP6071T-E/OT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2005 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6071 |
| Pin Count | 5 |
| Output Type | Rail-to-Rail |
| Number of Channels | 1 |
| Nominal Supply Current | 110μA |
| Output Current | 28mA |
| Current - Supply | 110μA |
| Slew Rate | 0.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 72 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~6V |
| Input Offset Voltage (Vos) | 150μV |
| Bandwidth | 1.2MHz |
| Unity Gain BW-Nom | 1200 kHz |
| Voltage Gain | 115dB |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Height | 1.3mm |
| Length | 3.1mm |
| Width | 1.8mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6071T-E/OT Overview
There is a SC-74A, SOT-753 case in which the instrumentation amplifier is packaged. The instrumentation amplifier in this picture is of the General Purpose-type. There is a Tape & Reel (TR) case that is delivered with the instrumentation amplifiers. It is estimated that there will be at least 5 terminations this year. In this case, there are 5 pins on the board. I would like to remind you that this buffer op amp should be powered by an 3V battery. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. An 5-pin op amp ic is included in the package. With regard to input offset voltage, instrumentation amplifier is rated at 150μV. This electronic part is recommended for mounting type Surface Mount. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureThere should be no change in the voltage gain at 115dB. Buffer op amp is equipped with 1 channels on the device. One of its many advantages is that buffer op amp outputs Rail-to-Rail signals. A TAPE AND REEL-shaped amplifier is used to pack the buffer amps. There is a recommendation that this electrical part be used with a supply with 110μA current rating.
MCP6071T-E/OT Features
5 Pins
supply voltage of 3V
115dB voltage gain
Output Type: Rail-to-Rail
MCP6071T-E/OT Applications
There are a lot of Microchip Technology MCP6071T-E/OT Instrumentational OP Amps applications.
- Precision measurement
- Power control
- Commercial audio systems
- Large motor controllers
- Switching amplifier
- Test equipment
- Polarized electrodes
- High speed sample
- single/dual op amp sum and difference circuits
- Automotive sensors
