MCP6072T-E/MNY
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-WFDFN Exposed Pad |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2010 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6072 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Number of Channels | 2 |
| Nominal Supply Current | 110μA |
| Output Current | 28mA |
| Current - Supply | 110μA |
| Slew Rate | 0.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 72 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~6V |
| Input Offset Voltage (Vos) | 150μV |
| Bandwidth | 1.2MHz |
| Unity Gain BW-Nom | 1200 kHz |
| Voltage Gain | 115dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.0001μA |
| Height | 750μm |
| Length | 2mm |
| Width | 3mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6072T-E/MNY Overview
A 8-WFDFN Exposed Pad case is used to package the op amp. Op amps are General Purpose types of amplifier on the chip. There is a Tape & Reel (TR) case that is delivered with the instrumentation amplifiers. A total of 8 terminations have been reported in the past few weeks. The total number of pins on linear amplifier is 8. Please take in mind that op amp should be run at 3V. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. It has 8 pins that make up the linear amplifier. In terms of the input offset voltage, instrumentation amplifier rates at 150μV. For this electrical component, Surface Mount is the recommended mounting type. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~125°C . You should keep the voltage gain at 115dB for the time being. There are a total of 2 channels available on the op amps. Buffer amplifier produces Rail-to-Rail signals, which is one of its many benefits. To pack the operational amplifier ics, TAPE AND REEL is adopted as the packing method. This electronic part is recommended to be used with an 110μA supply for best performance.
MCP6072T-E/MNY Features
8 Pins
supply voltage of 3V
115dB voltage gain
Output Type: Rail-to-Rail
MCP6072T-E/MNY Applications
There are a lot of Microchip Technology MCP6072T-E/MNY Instrumentational OP Amps applications.
- Industrial applications including automation
- Blood pressure sensors
- Inverse/same-phase proportional circuit
- Proportional counter tubes
- Video computer boards
- Automatic control
- High-frequency data acquisition systems
- Micro signal measurement
- single/dual op amp sum and difference circuits
- Car stereo
