MCP6074-E/ST
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2003 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6074 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Power Supplies | 2/5V |
| Number of Channels | 4 |
| Operating Supply Current | 110μA |
| Nominal Supply Current | 110μA |
| Output Current | 28mA |
| Slew Rate | 0.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 72 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~6V |
| Output Current per Channel | 28mA |
| Input Offset Voltage (Vos) | 150μV |
| Bandwidth | 1.2MHz |
| Unity Gain BW-Nom | 1200 kHz |
| Voltage Gain | 115dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Max Frequency | 10kHz |
| Bias Current-Max (IIB) @25C | 0.0001μA |
| Programmable Power | NO |
| Height | 1.05mm |
| Length | 5.1mm |
| Width | 4.5mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6074-E/ST Overview
There is a 14-TSSOP (0.173, 4.40mm Width) case package that contains the instrumentation amplifiers. This is a General Purpose type op amp. The op amp is delivered to you in a Tube case. In recent months, the number of terminations has approached 14. In total, there are 14 pins on this op amp ic. It would be helpful if you could remember that this op amp ic should be powered by an 3V battery. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. The buffer op amp includes 14 pins. Op amp rates 150μV as input offset voltage. For this electronic part, it is recommended that you mount it with type Surface Mount. In relation to the operating temperature of this buffer op amp, it works well at an average of -40°C~125°C . An 110μA volt supply current is needed for this linear amplifier to operate. There should be no change in the voltage gain. Instrumentation amplifier has 4 channels on it. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages.
MCP6074-E/ST Features
14 Pins
supply voltage of 3V
115dB voltage gain
Output Type: Rail-to-Rail
MCP6074-E/ST Applications
There are a lot of Microchip Technology MCP6074-E/ST Instrumentational OP Amps applications.
- Professional videography
- Automatic control
- Exponential operation circuits
- Video data acquisition
- Video conversion and routing
- Micro signal measurement
- High input resistance broadband
- Weak signal detection
- Proportional operation circuits
- Industrial applications including automation
