MCP607T-I/SN
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Published | 2004 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP607 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5.5V |
| Number of Elements | 2 |
| Operating Supply Current | 18.7μA |
| Nominal Supply Current | 25μA |
| Output Current | 17mA |
| Slew Rate | 0.08V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 75 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~6V |
| Output Current per Channel | 17mA |
| Input Offset Voltage (Vos) | 250μV |
| Bandwidth | 155 kHz |
| Unity Gain BW-Nom | 155 kHz |
| Voltage Gain | 121dB |
| Power Supply Rejection Ratio (PSRR) | 80dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Height Seated (Max) | 1.75mm |
| Length | 4.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP607T-I/SN Overview
There is a 8-SOIC (0.154, 3.90mm Width) case package that contains the instrumentation amplifiers. The instrumentation amplifier in this picture is of the General Purpose-type. It comes in a Tape & Reel (TR) case, which protects instrumentation amplifier from damage during delivery. There have been a total of 8 terminations over the past year. In this case, there are 8 pins on the board. Please take in mind that op amp should be run at 5V. Instrumentation amplifier is a part of Operational Amplifier. A total of 8 pins are present on the instrumentation amplifier. There is an input offset voltage of 250μV for this buffer op amp. This electronic part is best mounted with type Surface Mount. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~85°C . As long as the supply current of the chip does not exceed 18.7μA, this op amp ic can operate. Keeping the voltage gain at 121dB is the best course of action. One of the many benefits of this op amp ic is that it emits Rail-to-Rail signals. There is an operating supply voltage rating of 2 for this operational amplifier, which is rated at the manufacturer. The operating supply voltage of instrumentation amplifier is rated 5.5V voltage. TAPE AND REEL is adopted to pack the instrumentation amplifier.
MCP607T-I/SN Features
8 Pins
supply voltage of 5V
121dB voltage gain
Output Type: Rail-to-Rail
MCP607T-I/SN Applications
There are a lot of Microchip Technology MCP607T-I/SN Instrumentational OP Amps applications.
- Test and measurement instruments
- Medical instruments
- High speed sample
- Weighing systems
- Measurements of Wheatstone bridge
- High/low-pass filter circuit
- Communication
- Car stereo
- Polarized electrodes
- Non-polarized electrodes
