MCP607T-I/ST
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Published | 2000 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP607 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5.5V |
| Number of Elements | 2 |
| Operating Supply Current | 18.7μA |
| Nominal Supply Current | 25μA |
| Output Current | 17mA |
| Slew Rate | 0.08V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 75 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~6V |
| Output Current per Channel | 17mA |
| Input Offset Voltage (Vos) | 250μV |
| Bandwidth | 155 kHz |
| Unity Gain BW-Nom | 155 kHz |
| Voltage Gain | 121dB |
| Power Supply Rejection Ratio (PSRR) | 80dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Length | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP607T-I/ST Overview
Packaging for the buffer amplifier is in the form of a 8-TSSOP (0.173, 4.40mm Width) case. Op amps are General Purpose types of amplifier on the chip. The case in which buffer amplifier is delivered is called a Tape & Reel (TR) case. The number of terminations approaches 8. A total of 8 pins are located on this board. The linear amplifier should be run at 5V at all times, so please keep that in mind when using it. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. In total, the buffer amplifier consists of 8 pins. With regard to input offset voltage, instrumentation amplifier is rated at 250μV. This electronic part is recommended for mounting type Surface Mount. According to the manufacturer, this buffer op amp works well at -40°C~85°C , which is a good operating temperature. In order for this instrumentation amplifier to operate, the supply current needs to be between 18.7μA and 10 . 121dB should be the voltage gain. A benefit of this op amp ic is that it outputs Rail-to-Rail signals, which is one of the many advantages it has to offer. A total of 2 elements are present in this linear amplifier. The operating supply voltage of instrumentation amplifier is rated 5.5V voltage. As a result of this, the buffer amplifier is packed in TAPE AND REEL.
MCP607T-I/ST Features
8 Pins
supply voltage of 5V
121dB voltage gain
Output Type: Rail-to-Rail
MCP607T-I/ST Applications
There are a lot of Microchip Technology MCP607T-I/ST Instrumentational OP Amps applications.
- RF cable systems
- Video amplifiers
- Signal transformation
- single/dual op amp sum and difference circuits
- Subtraction operation circuits
- Semiconductor detectors
- Division circuits
- Test equipment
- Broadcasting
- Thermocouples
