MCP608-I/P
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2008 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | NOT APPLICABLE |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | NOT APPLICABLE |
| Base Part Number | MCP608 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5.5V |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Operating Supply Current | 18.7μA |
| Nominal Supply Current | 25μA |
| Output Current | 17mA |
| Slew Rate | 0.08V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 75 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~6V |
| Output Current per Channel | 17mA |
| Input Offset Voltage (Vos) | 250μV |
| Bandwidth | 155 kHz |
| Unity Gain BW-Nom | 155 kHz |
| Voltage Gain | 121dB |
| Power Supply Rejection Ratio (PSRR) | 80dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Max Frequency | 1kHz |
| Programmable Power | NO |
| Height | 4.953mm |
| Length | 10.16mm |
| Width | 7.112mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP608-I/P Overview
A 8-DIP (0.300, 7.62mm) case is used to package the op amp. A General Purpose-type buffer amplifier is shown here. Upon delivery, op amp ic is packaged in a Tube case. It is estimated that there will be at least 8 terminations this year. A total of 8 pins are attached to buffer op amp. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. The buffer op amp includes 8 pins. The input offset voltage is 250μV. This electronic component is recommended to be mounted using the mounting type Through Hole. With regard to operating temperature, this op amp functions well at -40°C~85°C. You can run this op amp ic on 18.7μA . Op amp is a member of the 121dB's 121dB family. There are a total of 1 channels available on the op amps. One of its many advantages is that buffer op amp outputs Rail-to-Rail signals. The operating supply voltage of instrumentation amplifier is rated 5.5V voltage.
MCP608-I/P Features
8 Pins
supply voltage of 5V
121dB voltage gain
Output Type: Rail-to-Rail
MCP608-I/P Applications
There are a lot of Microchip Technology MCP608-I/P Instrumentational OP Amps applications.
- Ultrasound transducers
- Video data acquisition
- Hand-held batteries
- Digital cameras
- earphone
- RF cable systems
- Division circuits
- Information processing
- Integrator circuits
- High-frequency data acquisition systems
