Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
8-SOIC (0.154, 3.90mm Width) |
Number of Pins |
8 |
Operating Temperature |
-40°C~85°C |
Packaging |
Tube |
Published |
2009 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
8 |
ECCN Code |
EAR99 |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Operational Amplifier |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
5V |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
MCP608 |
Pin Count |
8 |
Output Type |
Rail-to-Rail |
Operating Supply Voltage |
5.5V |
Power Supplies |
3/5V |
Number of Channels |
1 |
Nominal Supply Current |
25μA |
Output Current |
17mA |
Current - Supply |
18.7μA |
Slew Rate |
0.08V/μs |
Architecture |
VOLTAGE-FEEDBACK |
Amplifier Type |
General Purpose |
Common Mode Rejection Ratio |
75 dB |
Current - Input Bias |
1pA |
Voltage - Supply, Single/Dual (±) |
2.5V~6V |
Input Offset Voltage (Vos) |
250μV |
Bandwidth |
155 kHz |
Unity Gain BW-Nom |
155 kHz |
Voltage Gain |
121dB |
Power Supply Rejection Ratio (PSRR) |
80dB |
Low-Offset |
YES |
Frequency Compensation |
YES |
Supply Voltage Limit-Max |
7V |
Low-Bias |
YES |
Micropower |
YES |
Programmable Power |
NO |
Height |
1.25mm |
Length |
4.9mm |
Width |
3.9mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
MCP608-I/SN Overview
There is a 8-SOIC (0.154, 3.90mm Width) case in which the instrumentation amplifier is packaged. A General Purpose-type buffer amplifier is shown here. There is a Tube case that is delivered with the instrumentation amplifiers. There is a growing number of terminations approaching the number of 8. There are a total of 8 pins on this op amp. As a reminder, this buffer op amp should be powered by 5V battery and that the battery should be inserted in the amplifier. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. The op amp ic has an array of 8 pins on it. Op amp ic rates 250μV for input offset voltage. Surface Mount is the recommended mounting type of operational amplifiers. In terms of operating temperature, this instrumentation amplifier is well suited to a temperature range of -40°C~85°C. There should be no change in the voltage gain at 121dB. Op amp ic has 1 channels. This op amp ic outputs Rail-to-Rail signals, which is one of the many benefits it has. The operating supply voltage of the buffer op amp is rated at 5.5V. For optimal performance, this electrical part should be connected to a supply with a current of 18.7μA.
MCP608-I/SN Features
8 Pins
supply voltage of 5V
121dB voltage gain
Output Type: Rail-to-Rail
MCP608-I/SN Applications
There are a lot of Microchip Technology MCP608-I/SN Instrumentational OP Amps applications.
- Industrial control system
- Navigation
- Micro signal measurement
- Signal amplification
- Television
- Voltage regulation circuit
- Radar
- Division circuits
- Polarized electrodes
- Logarithmic operation circuits