MCP608-I/ST
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP608 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5.5V |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Operating Supply Current | 18.7μA |
| Nominal Supply Current | 25μA |
| Output Current | 17mA |
| Slew Rate | 0.08V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 75 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~6V |
| Output Current per Channel | 17mA |
| Input Offset Voltage (Vos) | 250μV |
| Bandwidth | 155 kHz |
| Unity Gain BW-Nom | 155 kHz |
| Voltage Gain | 121dB |
| Power Supply Rejection Ratio (PSRR) | 80dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Height | 1mm |
| Length | 3mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP608-I/ST Overview
There is a 8-TSSOP (0.173, 4.40mm Width) case package that contains the instrumentation amplifiers. Buffer amps of this type are called General Purpose-types. The case in which buffer amplifier is delivered is called a Tube case. A total of 8 terminations have been reported in the past few weeks. The pins on this board total to 8 in total. It is important to remember that this op amp should be operated at a voltage of 5V volts. It should be noted that this op amp is a type of Operational Amplifier device. In total, the buffer amplifier consists of 8 pins. Op amp rates 250μV as input offset voltage. Surface Mount is the recommended mounting type for this linear amplifier. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~85°C for optimal performance. You can run this op amp ic on 18.7μA . Maintain 121dB as the voltage gain. There are 1 channels on the operational amplifiers. One of the many benefits of this op amp ic is that it emits Rail-to-Rail signals. The operating supply voltage of instrumentation amplifier is rated 5.5V voltage.
MCP608-I/ST Features
8 Pins
supply voltage of 5V
121dB voltage gain
Output Type: Rail-to-Rail
MCP608-I/ST Applications
There are a lot of Microchip Technology MCP608-I/ST Instrumentational OP Amps applications.
- earphone
- Fission chambers
- Video conversion and routing
- Ultrasound transducers
- PDA
- RF cable systems
- Communication device
- Semiconductor detectors
- Exponential operation circuits
- Mobile phone
