MCP608T-I/ST
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP608 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5.5V |
| Number of Elements | 1 |
| Power Supplies | 3/5V |
| Nominal Supply Current | 25μA |
| Output Current | 17mA |
| Current - Supply | 18.7μA |
| Slew Rate | 0.08V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 75 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~6V |
| Input Offset Voltage (Vos) | 250μV |
| Bandwidth | 155 kHz |
| Unity Gain BW-Nom | 155 kHz |
| Voltage Gain | 121dB |
| Power Supply Rejection Ratio (PSRR) | 80dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Length | 4.4mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP608T-I/ST Overview
In the package, you will find a 8-TSSOP (0.173, 4.40mm Width)-case to contain the op amp ic. This is a General Purpose type op amp. The case in which buffer amplifier is delivered is called a Tape & Reel (TR) case. During the past two weeks, there have been close to 8 terminations. In this case, there are 8 pins on the board. The linear amplifier should be run at 5V at all times, so please keep that in mind when using it. In order to be more specific, this instrumentation amplifier is one of the types of Operational Amplifier devices. 8 pins are located on the operational amplifiers. Op amp rates 250μV as input offset voltage. It is recommended that this electronic component be mounted using the Surface Mount mounting type. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~85°C for optimal performance. The voltage gain should stay at 121dB. One of the many advantages that this linear amplifier has, among many other things, is the fact that it outputs Rail-to-Rail signals. There are a total of 1 elements in this linear amplifier. The operating supply voltage of the buffer op amp is rated at 5.5V. TAPE AND REEL is adopted to pack the instrumentation amplifier. For optimal performance, this electrical part should be connected to a supply with a current of 18.7μA.
MCP608T-I/ST Features
8 Pins
supply voltage of 5V
121dB voltage gain
Output Type: Rail-to-Rail
MCP608T-I/ST Applications
There are a lot of Microchip Technology MCP608T-I/ST Instrumentational OP Amps applications.
- Large motor controllers
- Broadcasting
- Blood pressure sensors
- Fast A/D and D/A converters
- High input resistance broadband
- High speed sample
- Addition operation circuits
- Wireless base stations
- Automation control systems
- Non-polarized electrodes
