MCP609-I/P
| Parameters | |
|---|---|
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2000 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | NOT APPLICABLE |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | NOT APPLICABLE |
| Base Part Number | MCP609 |
| Pin Count | 14 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5.5V |
| Number of Elements | 4 |
| Operating Supply Current | 18.7μA |
| Nominal Supply Current | 25μA |
| Output Current | 17mA |
| Min Input Voltage | 2.5V |
| Slew Rate | 0.08V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 75 dB |
| Current - Input Bias | 1pA |
| Max Input Voltage | 6V |
| Voltage - Supply, Single/Dual (±) | 2.5V~6V |
| Output Current per Channel | 17mA |
| Input Offset Voltage (Vos) | 250μV |
| Bandwidth | 155 kHz |
| Unity Gain BW-Nom | 155 kHz |
| Voltage Gain | 121dB |
| Average Bias Current-Max (IIB) | 0.00008μA |
| Power Supply Rejection Ratio (PSRR) | 80dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Max Frequency | 1kHz |
| Programmable Power | NO |
| Height | 4.953mm |
| Length | 19.69mm |
| Width | 7.112mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Number of Pins | 14 |
MCP609-I/P Overview
In order to protect the op amps, a 14-DIP (0.300, 7.62mm) case is used. Buffer amps of this type are called General Purpose-types. A Tube case is used for delivering the op amp. A total of 14 terminations have been reported in the past few weeks. It consists of a total of 14 pins in total. I would like to remind you that this buffer op amp should be powered by an 5V battery. Instrumentation amplifier is a part of Operational Amplifier. 14 pins are located on the operational amplifiers. There is an input offset voltage of 250μV for this buffer op amp. For this electrical component, Through Hole is the recommended mounting type. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~85°C for optimal performance. A supply current of 18.7μA can be used to operate this linear amplifier. The voltage gain should stay at 121dB. One of its many advantages is that buffer op amp outputs Rail-to-Rail signals. A voltage rating of 4 is indicated for the op amp's operating supply voltage. The operating supply voltage of instrumentation amplifier is rated 5.5V voltage.
MCP609-I/P Features
14 Pins
supply voltage of 5V
121dB voltage gain
Output Type: Rail-to-Rail
MCP609-I/P Applications
There are a lot of Microchip Technology MCP609-I/P Instrumentational OP Amps applications.
- Oscilloscopes
- Digital cameras
- Power generator
- Communication device
- Comparator
- Fast A/D and D/A converters
- Video conversion and routing
- RF cable systems
- earphone
- Commercial audio systems
