MCP6141-I/MS

1pA 60 dB Instrumentational OP Amps 1.4V~6V MCP6141 8 Pins 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)

Manufacturer: Microchip Technology
Nocochips NO: 536-MCP6141-I/MS
Package: 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)
Datasheet: PDF
Stock: 963
Description: 1pA 60 dB Instrumentational OP Amps 1.4V~6V MCP6141 8 Pins 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	8-TSSOP, 8-MSOP (0.118, 3.00mm Width)
Number of Pins	8
Operating Temperature	-40°C~85°C
Packaging	Tube
Published	2002
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	8
ECCN Code	EAR99
Terminal Finish	Matte Tin (Sn)
Subcategory	Operational Amplifier
Technology	CMOS
Terminal Position	DUAL
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	1
Supply Voltage	5V
Terminal Pitch	0.65mm
Time@Peak Reflow Temperature-Max (s)	40
Base Part Number	MCP6141
Pin Count	8
Output Type	Rail-to-Rail
Number of Elements	1
Nominal Supply Current	600nA
Output Current	21mA
Current - Supply	600nA
Slew Rate	0.003V/μs
Architecture	VOLTAGE-FEEDBACK
Amplifier Type	General Purpose
Common Mode Rejection Ratio	60 dB
Current - Input Bias	1pA
Voltage - Supply, Single/Dual (±)	1.4V~6V
Input Offset Voltage (Vos)	3mV
Gain Bandwidth Product	100kHz
Unity Gain BW-Nom	100 kHz
Voltage Gain	115dB
Power Supply Rejection Ratio (PSRR)	70dB
Low-Offset	NO
Supply Voltage Limit-Max	7V
Current - Output / Channel	20mA
Low-Bias	YES
Micropower	YES
Programmable Power	NO
Wideband	NO
Height	850μm
Length	3mm
Width	3mm
Radiation Hardening	No
RoHS Status	ROHS3 Compliant
Lead Free	Lead Free

MCP6141-I/MS Overview

A 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case is used to package the op amp. There are two types of operational amplifiers in this circuit. A Tube case is used for delivering the op amp. The number of terminations is approaching the 8 mark. There are a total of 8 pins on this op amp. Please take in mind that op amp should be run at 5V. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. In total, the buffer amplifier consists of 8 pins. There is an input offset voltage of 3mV for this buffer op amp. This electrical part should be mounted using type Surface Mount. According to the manufacturer, this buffer op amp works well at -40°C~85°C , which is a good operating temperature. Keeping the voltage gain at 115dB is the best course of action. On the output type, there are Rail-to-Rail different types of op amps. It is possible to count 1 elements on this buffer amplifier. We recommend that you use this electronic part with an 600nA supply in order to get the best performance from it.