MCP6141T-I/SN
| Parameters | |
|---|---|
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Wideband | NO |
| Length | 4.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6141 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Number of Elements | 1 |
| Nominal Supply Current | 600nA |
| Output Current | 21mA |
| Current - Supply | 600nA |
| Slew Rate | 0.003V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.4V~6V |
| Input Offset Voltage (Vos) | 3mV |
| Gain Bandwidth Product | 100kHz |
| Unity Gain BW-Nom | 100 kHz |
| Voltage Gain | 115dB |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Supply Voltage Limit-Max | 7V |
| Current - Output / Channel | 20mA |
MCP6141T-I/SN Overview
There is a 8-SOIC (0.154, 3.90mm Width) case package that contains the instrumentation amplifiers. There are two types of operational amplifiers in this circuit. There is a Tape & Reel (TR) case that is delivered with the instrumentation amplifiers. It is estimated that there will be 8 terminations in the next few months. There are a total of 8 pins on this op amp. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. 8 pins are available on the instrumentation amplifier. There is an input offset voltage of 3mV for this buffer op amp. This electrical part should be mounted using type Surface Mount. In terms of operating temperatures, this buffer amplifier works very well at a temperature of around -40°C~85°C . You should keep the voltage gain at 115dB for the time being. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages. There is a rating of 1 for the operating supply voltage of the buffer op amp. It is used TAPE AND REEL to pack the op amps. As a recommendation, this electronic component should be used with a power supply that can deliver 600nA.
MCP6141T-I/SN Features
8 Pins
supply voltage of 5V
115dB voltage gain
Output Type: Rail-to-Rail
MCP6141T-I/SN Applications
There are a lot of Microchip Technology MCP6141T-I/SN Instrumentational OP Amps applications.
- Strain gauges
- Measurements of Wheatstone bridge
- Broadcasting
- Automotive sensors
- Industrial applications including automation
- Gaming industry
- earphone
- Integrator circuits
- Fission chambers
- Logarithmic operation circuits
