MCP6142T-E/SN
| Parameters | |
|---|---|
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6142 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Number of Elements | 2 |
| Power Supplies | 1.5/5V |
| Nominal Supply Current | 600nA |
| Output Current | 21mA |
| Current - Supply | 600nA |
| Slew Rate | 0.003V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.4V~6V |
| Input Offset Voltage (Vos) | 3mV |
| Gain Bandwidth Product | 100kHz |
| Unity Gain BW-Nom | 100 kHz |
| Voltage Gain | 115dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES AVCL>=10 |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Height Seated (Max) | 1.75mm |
| Length | 4.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
MCP6142T-E/SN Overview
There is a 8-SOIC (0.154, 3.90mm Width) case package that contains the instrumentation amplifiers. Buffer amps of this type are called General Purpose-types. A Tape & Reel (TR) case is used to deliver the buffer op amp. It is estimated that there will be at least 8 terminations this year. It consists of a total of 8 pins in total. Please take in mind that op amp should be run at 5V. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. It has 8 pins that make up the linear amplifier. With regards to the offset voltage of the input, buffer amplifier is rated at 3mV. For this electronic part, it is recommended that you mount it with type Surface Mount. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~125°C . There should be no change in the voltage gain. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. It is possible to count 2 elements on this buffer amplifier. For the packing of the instrumentation amplifier, TAPE AND REEL is adopted. We recommend that you use this electronic part with an 600nA supply in order to get the best performance from it.
MCP6142T-E/SN Features
8 Pins
supply voltage of 5V
115dB voltage gain
Output Type: Rail-to-Rail
MCP6142T-E/SN Applications
There are a lot of Microchip Technology MCP6142T-E/SN Instrumentational OP Amps applications.
- Multimedia playback equipment
- Digital cameras
- High input resistance broadband
- Tablets
- Active probe
- Navigation
- Blood pressure sensors
- Test and measurement instruments
- Hand-held batteries
- Scintillation detectors
