MCP6144-E/ST
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6144 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Power Supplies | 1.5/5V |
| Number of Channels | 4 |
| Number of Circuits | 4 |
| Nominal Supply Current | 600nA |
| Output Current | 21mA |
| Slew Rate | 0.003V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.4V~6V |
| Input Offset Voltage (Vos) | 3mV |
| Bandwidth | 100 kHz |
| Unity Gain BW-Nom | 100 kHz |
| Voltage Gain | 115dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES AVCL>=10 |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Max Frequency | 1kHz |
| Height | 1.05mm |
| Length | 5.1mm |
| Width | 4.5mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6144-E/ST Overview
There is a 14-TSSOP (0.173, 4.40mm Width) case in which the instrumentation amplifier is packaged. Op amps are General Purpose types of amplifier on the chip. In the case of Tube cases, linear amplifier will be delivered. There is a growing number of terminations approaching the number of 14. In total, there are 14 pins on this op amp ic. Please take in mind that this instrumentation amplifier should be run at 5V. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. The buffer op amp includes 14 pins. The input offset voltage is 3mV. This electronic part is best mounted with type Surface Mount. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureVoltage gain should remain at 115dB. This op amp ic has 4 circuits. On the buffer amps, there are 4 channels that can be used. In addition to outputting Rail-to-Rail signals, this op amp ic offers a number of other advantages.
MCP6144-E/ST Features
14 Pins
supply voltage of 5V
115dB voltage gain
Output Type: Rail-to-Rail
MCP6144-E/ST Applications
There are a lot of Microchip Technology MCP6144-E/ST Instrumentational OP Amps applications.
- Oscilloscopes
- High gain DC amplifier
- Portable docking station
- Multimedia playback equipment
- Micro signal measurement
- Power generator
- Mobile phone
- Active probe
- MP3
- Commercial audio systems
