MCP6144T-E/ST
| Parameters | |
|---|---|
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6144 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Number of Elements | 4 |
| Power Supplies | 1.5/5V |
| Nominal Supply Current | 600nA |
| Output Current | 21mA |
| Current - Supply | 600nA |
| Slew Rate | 0.003V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.4V~6V |
| Input Offset Voltage (Vos) | 3mV |
| Gain Bandwidth Product | 100kHz |
| Unity Gain BW-Nom | 100 kHz |
| Voltage Gain | 115dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES AVCL>=10 |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Height Seated (Max) | 1.2mm |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
MCP6144T-E/ST Overview
There is a 14-TSSOP (0.173, 4.40mm Width) case in which the instrumentation amplifier is packaged. General Purpose-type instrumentation amplifiers are used in this application. A Tape & Reel (TR) case is used to deliver the buffer op amp. In recent months, the number of terminations has approached 14. In this case, there are 14 pins on the board. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. To be specific, this instrumentation amplifier is a type of Operational Amplifier. In total, the buffer amplifier consists of 14 pins. With regards to the offset voltage of the input, buffer amplifier is rated at 3mV. For this electronic part, it is recommended that you mount it with type Surface Mount. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperature115dB should be the voltage gain. Buffer amplifier produces Rail-to-Rail signals, which is one of its many benefits. This linear amplifier has a total of 4 elements. The linear amplifier is packaged by using a TAPE AND REEL axis. This electronic part is recommended to be used with an 600nA supply for best performance.
MCP6144T-E/ST Features
14 Pins
supply voltage of 5V
115dB voltage gain
Output Type: Rail-to-Rail
MCP6144T-E/ST Applications
There are a lot of Microchip Technology MCP6144T-E/ST Instrumentational OP Amps applications.
- Large motor controllers
- Power control
- Image computer boards
- Addition operation circuits
- Active probe
- Video amplifiers
- High-frequency data acquisition systems
- Radar
- earphone
- Band-pass filter
