MCP622T-E/MF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-VDFN Exposed Pad |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2011 |
| Series | mCal Technology |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 2.5V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP622 |
| Pin Count | 10 |
| JESD-30 Code | S-PDSO-N10 |
| Output Type | Rail-to-Rail |
| Number of Elements | 2 |
| Power Supplies | 3/5V |
| Operating Supply Current | 2.5mA |
| Nominal Supply Current | 2.5mA |
| Output Current | 70mA |
| Slew Rate | 10V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 65 dB |
| Current - Input Bias | 5pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~5.5V |
| Output Current per Channel | 70mA |
| Input Offset Voltage (Vos) | 200μV |
| Gain Bandwidth Product | 20MHz |
| Unity Gain BW-Nom | 20000 kHz |
| Voltage Gain | 126dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 61dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6.5V |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Wideband | NO |
| Height Seated (Max) | 1mm |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MCP622T-E/MF Overview
A 8-VDFN Exposed Pad case is used to package the op amp. A General Purpose-type buffer amplifier is shown here. In the case of Tape & Reel (TR) cases, linear amplifier will be delivered. There is a growing number of terminations approaching the number of 10. In this case, there are 10 pins on the board. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 2.5V. It should be noted that this op amp is a type of Operational Amplifier device. 8 pins are available on the instrumentation amplifier. With regard to input offset voltage, instrumentation amplifier is rated at 200μV. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~125°C . The buffer amplifier is capable of operating from a supply current of 2.5mA . 126dB should be the voltage gain. One of its many advantages is that buffer op amp outputs Rail-to-Rail signals. 2 elements make up the design of this buffer amplifier. TAPE AND REEL is adopted to pack the instrumentation amplifier. The mCal Technology represents the op amp's series number.
MCP622T-E/MF Features
10 Pins
supply voltage of 2.5V
126dB voltage gain
Output Type: Rail-to-Rail
MCP622T-E/MF Applications
There are a lot of Microchip Technology MCP622T-E/MF Instrumentational OP Amps applications.
- Measurements of Wheatstone bridge
- Power transmission
- Proportional counter tubes
- earphone
- Radar
- Addition operation circuits
- Information processing
- Signal filtering
- Weighing systems
- Thermocouples
