MCP6232-E/SN
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2005 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6232 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5.5V |
| Number of Channels | 2 |
| Operating Supply Current | 20μA |
| Nominal Supply Current | 20μA |
| Output Current | 23mA |
| Min Input Voltage | 1.8V |
| Slew Rate | 0.15V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 61 dB |
| Current - Input Bias | 1pA |
| Max Input Voltage | 6V |
| Voltage - Supply, Single/Dual (±) | 1.8V~6V |
| Output Current per Channel | 23mA |
| Input Offset Voltage (Vos) | 5mV |
| Bandwidth | 300 kHz |
| Unity Gain BW-Nom | 300 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.0011μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Max Frequency | 1kHz |
| Height | 1.25mm |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6232-E/SN Overview
Packaged in a 8-SOIC (0.154, 3.90mm Width) case, the buffer op amp is ready to use. The instrumentation amplifier in this picture is of the General Purpose-type. A Tube case is used for delivering the op amp. It is estimated that there will be at least 8 terminations this year. A total of 8 pins are attached to buffer op amp. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. To be specific, this instrumentation amplifier is a type of Operational Amplifier. The op amp ic has an array of 8 pins on it. Op amp rates 5mV as input offset voltage. Surface Mount is the recommended mounting type for this linear amplifier. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureUsing an 20μA supply current, this operational amplifier ics can be operated. You should keep the voltage gain at 110dB for the time being. Instrumentation amplifier has 2 channels on it. Buffer amplifier produces Rail-to-Rail signals, which is one of its many benefits. The operating supply voltage of the buffer op amp is rated at 5.5V.
MCP6232-E/SN Features
8 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
MCP6232-E/SN Applications
There are a lot of Microchip Technology MCP6232-E/SN Instrumentational OP Amps applications.
- Subtraction operation circuits
- Cinema or auditorium audio system
- Proportional counter tubes
- Video conversion and routing
- Vehicle electronics
- Micro signal measurement
- Weak signal detection
- E-book readers
- Communication
- pH (acidity)
