MCP624-E/ST
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2010 |
| Series | mCal Technology |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 2.5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP624 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Power Supplies | 3/5V |
| Number of Channels | 4 |
| Nominal Supply Current | 2.5mA |
| Output Current | 70mA |
| Current - Supply | 2.5mA |
| Slew Rate | 10V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 65 dB |
| Current - Input Bias | 5pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~5.5V |
| Input Offset Voltage (Vos) | 200μV |
| Bandwidth | 20MHz |
| Unity Gain BW-Nom | 20000 kHz |
| Voltage Gain | 126dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 61dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6.5V |
| Current - Output / Channel | 70mA |
| Low-Bias | YES |
| Height | 1.05mm |
| Length | 5.1mm |
| Width | 4.5mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP624-E/ST Overview
A 14-TSSOP (0.173, 4.40mm Width) case is used to package the op amp. This is a General Purpose type op amp. The op amp is delivered to you in a Tube case. It is estimated that there will be at least 14 terminations this year. Buffer amplifier has a total of 14 pins. It is important to remember that this op amp should be operated at a voltage of 2.5V volts. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. An 14-pin op amp ic is included in the package. In terms of the input offset voltage, instrumentation amplifier rates at 200μV. This electronic component is recommended to be mounted using the mounting type Surface Mount. In terms of operating temperature, this instrumentation amplifier is well suited to a temperature range of -40°C~125°C. There should be no change in the voltage gain at 126dB. There are 4 channels on the operational amplifiers. As one of the many benefits of this buffer amplifier, it puts out Rail-to-Rail signals, which is one of the many benefits it offers. To run supply current of buffer amplifier under 2.5mA. This buffer amplifier is assigned within the mCal Technology series by its manufacturer.
MCP624-E/ST Features
14 Pins
supply voltage of 2.5V
126dB voltage gain
Output Type: Rail-to-Rail
MCP624-E/ST Applications
There are a lot of Microchip Technology MCP624-E/ST Instrumentational OP Amps applications.
- Fission chambers
- Large motor controllers
- Measurements of Wheatstone bridge
- Cinema or auditorium audio system
- High gain DC amplifier
- Polarized electrodes
- Professional videography
- Active probe
- Differentiator circuits
- Video conversion and routing
