MCP6241-E/MS
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2008 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6241 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Power Supplies | 2/5V |
| Number of Channels | 1 |
| Operating Supply Current | 50μA |
| Nominal Supply Current | 50μA |
| Output Current | 23mA |
| Slew Rate | 0.3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~5.5V |
| Output Current per Channel | 23mA |
| Input Offset Voltage (Vos) | 5mV |
| Bandwidth | 550 kHz |
| Unity Gain BW-Nom | 550 kHz |
| Voltage Gain | 110dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Power | NO |
| Height | 850μm |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6241-E/MS Overview
In the package, you will find a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)-case to contain the op amp ic. A General Purpose-type buffer amplifier is shown here. It comes in a Tube case, which protects instrumentation amplifier from damage during delivery. A total of 8 terminations have been reported in the past few weeks. It consists of a total of 8 pins in total. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. An 8-pin op amp ic is included in the package. Op amp rates 5mV as input offset voltage. This electrical part should be mounted using type Surface Mount. In terms of operating temperature, this instrumentation amplifier is well suited to a temperature range of -40°C~125°C. A supply current of 50μA can be used to operate this linear amplifier. Voltage gain should remain at 110dB. Op amp ic has 1 channels. One of the many benefits of this op amp ic is that it emits Rail-to-Rail signals.
MCP6241-E/MS Features
8 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
MCP6241-E/MS Applications
There are a lot of Microchip Technology MCP6241-E/MS Instrumentational OP Amps applications.
- ECG equipment
- Weak signal detection
- Commercial audio systems
- Portable electronic products powered by batteries
- Signal amplification
- Signal transformation
- Medical instruments
- Broadcasting
- High gain DC amplifier
- Displayers for aircraft and air transportation control systems
