MCP6241UT-E/OT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6241 |
| Pin Count | 5 |
| Output Type | Rail-to-Rail |
| Number of Channels | 1 |
| Nominal Supply Current | 50μA |
| Output Current | 23mA |
| Current - Supply | 50μA |
| Slew Rate | 0.3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~5.5V |
| Input Offset Voltage (Vos) | 5mV |
| Bandwidth | 550 kHz |
| Unity Gain BW-Nom | 550 kHz |
| Voltage Gain | 110dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Current - Output / Channel | 23mA |
| Low-Bias | YES |
| Micropower | YES |
| Power | NO |
| Height | 1.3mm |
| Length | 3.1mm |
| Width | 1.8mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6241UT-E/OT Overview
There is a SC-74A, SOT-753 case package that contains the instrumentation amplifiers. A General Purpose-type buffer amplifier is shown here. A Tape & Reel (TR) case is used to deliver the buffer op amp. A total of 5 terminations have been reported in the past few weeks. There are a total of 5 pins on this op amp. I would like to remind you that this buffer op amp should be powered by an 5V battery. Instrumentation amplifier is a part of Operational Amplifier. A total of 5 pins are present on the instrumentation amplifier. Regarding input offset voltage, op amp rates 5mV. This electronic component is recommended to be mounted using the mounting type Surface Mount. With regard to operating temperature, op amp ranges -40°C~125°C. It is recommended to keep the voltage gain at 110dB at all times. 1 channels are available on the instrumentation amplifier. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. For packing the buffer amplifier, the TAPE AND REEL-axis is adopted. We recommend that you use this electronic part with an 50μA supply in order to get the best performance from it.
MCP6241UT-E/OT Features
5 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
MCP6241UT-E/OT Applications
There are a lot of Microchip Technology MCP6241UT-E/OT Instrumentational OP Amps applications.
- Portable electronic products powered by batteries
- Inverse/same-phase proportional circuit
- Tablets
- Gaming industry
- Addition operation circuits
- PDA
- Band-stop filter
- Power control
- Communication
- Video amplifiers
