MCP6242-E/P
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2000 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Base Part Number | MCP6242 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Number of Channels | 2 |
| Nominal Supply Current | 50μA |
| Output Current | 23mA |
| Current - Supply | 50μA |
| Slew Rate | 0.3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~5.5V |
| Input Offset Voltage (Vos) | 5mV |
| Bandwidth | 550 kHz |
| Unity Gain BW-Nom | 550 kHz |
| Voltage Gain | 110dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Current - Output / Channel | 23mA |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Power | NO |
| Height | 4.953mm |
| Length | 10.16mm |
| Width | 7.112mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6242-E/P Overview
There is a 8-DIP (0.300, 7.62mm) case package that contains the instrumentation amplifiers. There are two types of operational amplifiers in this circuit. As far as the packaging is concerned, buffer op amp is delivered in a Tube case. There is a growing number of terminations approaching the number of 8. In total, there are 8 pins on this op amp ic. This linear amplifier should be powered by an 5V battery. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. 8 pins are included on the operational amplifiers. In terms of input offset voltage, operational amplifier rates 5mV. For this electrical component, the recommended mounting type is Through Hole, which is the most common. With regard to operating temperature, op amp ranges -40°C~125°C. The voltage gain should stay at 110dB. There are a total of 2 channels available on the op amps. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. It is recommended that you use an 50μA power supply with this electrical part in order for it to operate correctly.
MCP6242-E/P Features
8 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
MCP6242-E/P Applications
There are a lot of Microchip Technology MCP6242-E/P Instrumentational OP Amps applications.
- Power control
- Displayers for aircraft and air transportation control systems
- Weak signal detection
- Precision measurement
- pH (acidity)
- Proportional counter tubes
- Video data acquisition
- Communication device
- Automatic control
- Professional videography
